2- Aerospace Engineering

BUSINESS DOCUMENT This document is intended for business use and should be distributed to intended recipients only. STUDENT NAME: STUDENT ID. NO. PROGRAMME: Applied Bachelor in Aerospace Engineering MODULE TITLE: Basic Aircraft Workshop Practices MODULE CODE: AE100 ASSESSED LEARNING OUTCOMES LO1 Understand the safe working practices associated with the care, control and use of aircraft workshop tools and equipment LO2 Be able to read and interpret aircraft engineering drawings and diagrams ✓ LO3 Be able to carry out airframe metalwork exercises LO4 Be able to remove, inspect and fit aircraft fasteners, fluid plumbing, transmission systems and aircraft control cable hardware LO5 Be able to carry out workshop fitting activities on aircraft electrical cables, terminations and fittings LO6 Know about soldering, brazing and welding. Student Declaration Submission requirement: I certify that the assignment submission is entirely my own work and I fully understand the consequences of plagiarism. All the sources from which information has been obtained for this assignment, have been referenced. I understand that making a false declaration is a form of malpractice. I further confirm that I have read and understood the Emirates Aviation University rules and regulations about plagiarism and copying and agree to be bound by them. 1. Signed cover sheet 2. Assignment report 3. Soft / Hard copy of turnitin report Student Signature: Submitted on: RESULT QUESTIONS Q1 Q2 Q3 Q4 Q5 OVERALL (26/100%) LEARNING OUTCOMES 3 3 3 3 3 TOTAL MARK 4 5 5 6 6 ACHIEVED MARK Assessor’s Overall Feedback: Assessor’s Name: TAREK OMAR Signature: Date: SCHOOL OF ENGINEERING FALL-2022 Page 1 of 3 BUSINESS DOCUMENT This document is intended for business use and should be distributed to intended recipients only. Submission Format The submission should be in the form of an MS Word document with appropriate use of structure and referencing, as per the below: 1. Preferred font is Arial and size 10. Heading size can be increased but make sure to keep the same format throughout this report. 2. 1.5x spacing is required between sentences. 3. The first page should have an introduction to the assignment, which should also contain your views. 4. The body should follow next. a. Notes should be typed and drawings presented neatly. Images/Pictures may be copied & pasted but need to be referenced. b. Headings, Images/Pictures, Used equations must be numbered for traceability purpose. 5. A brief conclusion should be at the end with your comments and views. 6. The last page should have your reference sources. Preferable style – Harvard style. Always make sure to write the source of the copied images/pictures. 7. The assignment should be submitted through turnitin Plagiarism Plagiarism is defined as the presentation of another person’s work as your own. It is a particular form of cheating. Plagiarism must be avoided at all costs and students who break the rules, however innocently, may be penalised. It is your responsibility to ensure that you understand correct referencing practices. As a university level student, you are expected to use appropriate references throughout and keep carefully detailed notes of all your sources of materials you have used in your work, including any material downloaded from the Internet. If this be the case, Emirates Aviation University considers plagiarism as theft and any student found to have plagiarised would be awarded an automatic fail for the piece of work submitted and may be excluded from further study at the University. FALL-2022 Page 2 of 3 BUSINESS DOCUMENT This document is intended for business use and should be distributed to intended recipients only. ASSIGNMENT TITLE: AIRFRAME METALWORK EXERCISE Assignment Brief and Guidance Scenario Assume that you have been selected as a junior intern to work in the Aircraft workshop for Phonetic Airlines. After completing six months you must submit a report presenting all the activities you have been part of in the aircraft workshop Questions FALL-2022 Page 3 of 3 BUSINESS DOCUMENT This document is intended for business use and should be distributed to intended recipients only. Flush Batch Repair Exercise : see the attached figure above Based on the workshop classes and valid sources answer the following Question 1 (04 marks) Describe the safety precautions that must be observed when a metal work task requires the use of pneumatic drills and pneumatic riveters. (04 marks) Question 2 (05 Marks) Determine from valid sources the correct sheet metals and rivet specification and procedure to be followed to produce a satisfactory repair on a given piece of airframe riveted structure or structural component. Question 3 (05 marks) Check if the given task is compliant to those spics and conditions. Question 4 (06 marks) Make a list of tools that were used to accomplish this task; write briefly about each tool. Question 5 (06 marks)